Heavy Duty Lathe Machine

Approx. Rs 6 Lakh / PieceGet Latest Price

We are the leading Manufacturers and supplier of the Heavy Duty Roll turning Lathe Machine for Forging Plants.

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:
Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:
It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:
Tail Stock is situated on the right side above the lathe bed.
It is used for:

Support the long end of the job for holding and minimizes its sagging.

It holds the tool for performing different operations like drilling, reaming, tapping, etc.

And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.

It gives rigid supports to the tool during operations.

It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:
Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:
It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:
It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:
It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:
An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:
A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:
Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:
Chuck is used to holding the work piece securely.

Features:

Rigid section straight wide bed with hardened and ground guide ways

Main spindle supported on precision ball bearings.

Pre-loaded Leading screws and nuts for Turning and Threading.

Rear tool post with tool holder.

Hardened Ground Head stock spindle and Tail sock sleeve

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Approx. Rs 3.25 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:
Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:
It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:
Tail Stock is situated on the right side above the lathe bed.
It is used for:

Support the long end of the job for holding and minimizes its sagging.

It holds the tool for performing different operations like drilling, reaming, tapping, etc.

And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.

It gives rigid supports to the tool during operations.

It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:
Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:
It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:
It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:
It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:
An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:
A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:
Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:
Chuck is used to holding the work piece securely.

Features:

Rigid section straight wide bed with hardened and ground guide ways

Main spindle supported on precision ball bearings.

Pre-loaded Leading screws and nuts for Turning and Threading.

Rear tool post with tool holder.

Hardened Ground Head stock spindle and Tail sock sleeve

Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Approx. Rs 2.5 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Approx. Rs 3 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Approx. Rs 2 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Approx. Rs 65,000 / PieceGet Latest Price

We have gained recognition as an eminent enterprise, devotedly engaged in manufacturing a broad range of Heavy duty Roll Turning Lathe Machine.

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:
Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:
It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:
Tail Stock is situated on the right side above the lathe bed.
It is used for:

Support the long end of the job for holding and minimizes its sagging.

It holds the tool for performing different operations like drilling, reaming, tapping, etc.

And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.

It gives rigid supports to the tool during operations.

It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:
Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:
It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:
It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:
It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:
An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:
A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:
Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:
Chuck is used to holding the work piece securely.

Features:

Rigid section straight wide bed with hardened and ground guide ways

Main spindle supported on precision ball bearings.

Pre-loaded Leading screws and nuts for Turning and Threading.

Rear tool post with tool holder.

Hardened Ground Head stock spindle and Tail sock sleeve

Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Additional Information:

Approx. Rs 6.5 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Approx. Rs 3.5 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Extra Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Approx. Rs 1.25 Lakh / PieceGet Latest Price

Esskay Lathe Group of Companies Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Additional Information:

Approx. Rs 9.75 Lakh / PieceGet Latest Price

With our decades of experience and in-depth knowledge of this industry, we are engaged in offering an excellent range of Heavy Duty Roll Turning Lathe Machine.

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Approx. Rs 3.5 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Approx. Rs 9.6 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Extra Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Approx. Rs 9 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Product Price :Get Latest Price

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve

Additional Information:

Product Price :Get Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Approx. Rs 13.5 Lakh / PieceGet Latest Price

Esskay Lathe & Machine Tools Manufacturers of All types and All Sizes of Extra Heavy duty lathe machines since 1978 and supplied all our machines worldwide.

Functions:

HEAD STOCK:

Head Stock is situated at the left side on the all types of horizontal lathe machines and it is the main part of the running mechanism and electrical mechanism of a Lathe machine.

BED:

It is the base of the lathe machine. It is made of the single-piece casting of  Cast Iron. The bed consists of two heavy metal slides running lengthwise, with ways or ‘V’ formed upon them and rigidly supported with cross girths.

TAILSTOCK:

Tail Stock is situated on the right side above the lathe bed.
It is used for:

• Support the long end of the job for holding and minimizes its sagging.
• It holds the tool for performing different operations like drilling, reaming, tapping, etc.
• And it is also used for a small amount of taper for a long job by offsetting the tailstock.

CARRIAGE:

• The carriage is used to support, guide, and feed the tool against the job when the machining is done. It holds moves and controls the cutting tool.
• It gives rigid supports to the tool during operations.
• It transfers power from feed rod to cutting tool through apron mechanism for longitudinal cross-feeding.

SADDLE:

Generally, it is made up of ‘H’ shaped casting and it has a ‘V’ guide and a flat guide for mounting it on the lathe bed guide ways.

CROSS SLIDE:

It is assembled on the top of the saddle. The top surface of the cross-slide is provided with T-slot

COUMPOUND REST:

It supports the tool post and cutting tool in its various positions. It can be swiveled at any desired position in the horizontal plane. It is necessary for turning angles and boring short tapers.

TOOL POST:

It is the topmost portion of the carriage and it is used to hold various cutting tools or tool holders.

APRON:

An apron is a house of the feed mechanism. It is fastened to the saddle and hangover in front of the bed.

LEAD SCREW:

A lead screw is also known as a power screw or a translation screw. It converts rotational motion to linear motion. Lead Screw is used for Thread Cutting operation in a lathe machine tool.

FEED ROD:

Feed rod is used to move the carriage from the left side to the right side and also from the right side to the left side

CHUCK:

Chuck is used to holding the work piece securely.

Features:

• Rigid section straight wide bed with hardened and ground guide ways
• Main spindle supported on precision ball bearings.
• Pre-loaded Leading screws and nuts for Turning and Threading.
• Rear tool post with tool holder.
• Hardened Ground Head stock spindle and Tail sock sleeve
• Bed ways- 3 v & 1 flat

Standard Accessories:
Steady Rest , Follow rest , Dead center, change gears, Safety cover.

Approx. Rs 2 Lakh / PieceGet Latest Price

Approx. Rs 3 Lakh / PieceGet Latest Price